[AandJCycles]

Finished this up tonight for a customer. Bike has free Spirits x-pipe and Forward controls. We chopped off the stock mufflers and welded up some cheapy 45 degree pieces and dime city mufflers. Customer provided these slick Billet aluminum tips.
https://youtu.be/Gi34z3MTZaA

For the lighting, we welded on new tabs on the rear fender bracket and mounted hightechspeed X-Arc multifunction Turn Signals. These are wired in as run/brake/turn signals and are Super bright. Also installed side mount plate kit and The just released Motone Bel Air tail light. Mounted the light on bottom to keep it away from the exhaust. Customer will be installed Bobber fender himself.
https://youtu.be/_Iga8lFe1Ok

 

[Bobber John]

looks good! I've got one question: aren't you going to put some kind of cover over the holes where the standard light was mounted? It would be great to have a cover for that area that you can order in your shop!
maybe something like Cdubs' creation: http://www.triumphbobberforum.com/forum/36769-post16.html

 

[Brandon Miller]

Exhaust sounds pretty beefy. Where are you guys located?

 

[MikenLbk]

What side plate mount is that?
Bike looks great.


Sent from my iPhone using Tapatalk

 

[AandJCycles]

What side plate mount is that?
Bike looks great.


Sent from my iPhone using Tapatalk

Customer supplied it but pretty sure it is the TC Bros one: http://www.tcbroschoppers.com/side-...MIyfmFgY7c1gIVDgaGCh0EGgnNEAQYASABEgKUx_D_BwE

We drilled out some new holes for the Motone tail light

 

[AandJCycles]

looks good! I've got one question: aren't you going to put some kind of cover over the holes where the standard light was mounted? It would be great to have a cover for that area that you can order in your shop!
maybe something like Cdubs' creation: http://www.triumphbobberforum.com/forum/36769-post16.html

John,
Customer will be chopping and painting the fender himself. Thanks for that link, I will talk to some of our vendors and try to come up with a solution.

 

[Bobber John]

John,
Customer will be chopping and painting the fender himself. Thanks for that link, I will talk to some of our vendors and try to come up with a solution.

Sorry - I overlooked that part in your first post... But I'm looking forward to your solution! Thank a lot!

 

[Olecharlie]

Man one sweet bike, love it!

 

[skipnewman]

Are those Biltwell bars?

 

[AandJCycles]

Are those Biltwell bars?

Bars are from Zombie Performance

 

[Ghostnote]

Bars are from Zombie Performance

Which ones, if you don't mind sharing? They're pretty fucking sick...

 

[AandJCycles]

Bars are from Zombie Performance

Which ones, if you don't mind sharing? They're pretty fucking sick...

Pretty sure they are the 6-bend pullbacks

 

[MikeB]

Can someone please measure the diameter of the rear fender bracket for me? Regrettably my Bobber is in off-site storage.

Rationale... I bought X-Arc front and rear signal lights. Similar to the Bobber that A&J Cycles customized, I'd like to try mounting the rear multi-function signal lights on the rear fender bracket. Rather than weld on tabs (too permanent for me at this time), I wanted to see if I could find a pair of black p-clamps that'd fit the rear fender bracket.

 

[PFEN]

@MikeB

is it this you need:nerd:
then: 8 x 35 mm




you can find the type on this list but I will go see on my if it is correct

one more thing,Mike.if you have difficulty finding bolts,it's a lot easier for us here and then you send them.it must not cost a fortune by mail.

https://www.triumphworld.de/product_info.php?products_id=205511&MODsid=hlkkc9rkbs1upvtkmdg1jq9nk1

 

[MikeB]

Many thanks for your efforts and your kind offer to source the bolt. However, I'm looking for the diameter of the bracket (#6 in the diagram) that supports the rear fender so that I can find a p-clamp that goes around the bracket that will support the rear signal light.

 

[Rons T]

I had the same idea. I measured it a while back and bought p clamps but went another direction. I recall buying 1 & 1 1/4 clamps and didn’t like the way either fit. In between these 2 would have been right for me.
Measure the circumference with a string or strip of paper. Divide that length by pi. That’s the diameter.

 

[MikeB]

I had the same idea. I measured it a while back and bought p clamps but went another direction. I recall buying 1 & 1 1/4 clamps and didn’t like the way either fit. In between these 2 would have been right for me.
Measure the circumference with a string or strip of paper. Divide that length by pi. That’s the diameter.

Thanks.

 

[Forjox]

Many thanks for your efforts and your kind offer to source the bolt. However, I'm looking for the diameter of the bracket (#6 in the diagram) that supports the rear fender so that I can find a p-clamp that goes around the bracket that will support the rear signal light.

5/8inch or 16mm

 

[MikeB]

5/8inch or 16mm

Many thanks!

 

[Christian Byhmer]

Finished this up tonight for a customer. Bike has free Spirits x-pipe and Forward controls. We chopped off the stock mufflers and welded up some cheapy 45 degree pieces and dime city mufflers. Customer provided these slick Billet aluminum tips.
https://youtu.be/Gi34z3MTZaA

For the lighting, we welded on new tabs on the rear fender bracket and mounted hightechspeed X-Arc multifunction Turn Signals. These are wired in as run/brake/turn signals and are Super bright. Also installed side mount plate kit and The just released Motone Bel Air tail light. Mounted the light on bottom to keep it away from the exhaust. Customer will be installed Bobber fender himself.
https://youtu.be/_Iga8lFe1Ok

Really like the look the x-arc tail light gives. Did you end up welding the fastening for them or did they fit on standard configuration?