Ignition Switch Wiring Harness & Clutch Cable Routing - Triumph Bobber Forum
 4Likes
  • 1 Post By brianw
  • 3 Post By eisen77
 
LinkBack Thread Tools
post #1 of 4 (permalink) Old 03-19-2018, 03:26 PM Thread Starter
Junior Member
 
Join Date: Apr 2017
Location: ontario canada
Posts: 22
Ignition Switch Wiring Harness & Clutch Cable Routing

My wife has a 2017 Bobber and I noticed that the wiring harness behind the switch is touching the engine case tightly. I just purchased a Bobber Black for myself and after going over the bike I noticed two things.


1. Ignition Switch Wiring has been re-routed so that it is no longer touching the engine case.


2. The Clutch Cable routing at the forks is no longer held by a clamp but sits in a plastic support so that it may move when turning the handle bars.


These are the changes I have seen thus far and they are good changes.


Therefore I will remove the ignition switch and try insulating the wiring on the back of my wife's 2017 Bobber.
catchoreno likes this.
brianw is offline  
post #2 of 4 (permalink) Old 03-19-2018, 07:06 PM
Senior Member
 
Join Date: May 2017
Location: California
Posts: 149
Thanks for pointing that out. I will take a look at mine and make sure it is not touching.
Spridal is offline  
post #3 of 4 (permalink) Old 03-27-2018, 09:53 AM
Member
 
catchoreno's Avatar
 
Join Date: Feb 2018
Location: USA Delaware
Posts: 55
Pictures ? if possible thanks

Life is what you make it.
catchoreno is offline  
Sponsored Links
Advertisement
 
post #4 of 4 (permalink) Old 03-28-2018, 09:01 AM
Super Moderator
 
eisen77's Avatar
 
Join Date: Feb 2017
Location: Palma de Mallorca
Posts: 3,073
I went to visit the dealer and have a look at the Bobber Black cabling versus the 2017 Bobber.
First of all he assured me that (for now) there is no recall nor notice about the 2017 cable route. It is properly insulated and positioned on top of the engine on all 2017 bikes.

The Bobber Black´s cable has indeed been rerouted and has a better overall finish, but as such is only less visible. It is still touching the top of the engine and exposed to the same amount of heat.
But yes, it does look neater on the Black model and less of an ´afterthought´.
I think that with the new routing, moving the ignition to the LHS (like on my bike) would be much harder as there is no more slack in the cable.

Here are some pics of the Bobber BLACK:






And the 2017:
ysoslo, MX429 and PFEN like this.
eisen77 is online now  
Reply

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
New Product - Viba Wiring Harness Cover AandJCycles A & J Cycles 28 06-08-2019 12:31 PM
Clutch Cable Wedge Triumph Bobber Issues And Problems 27 11-07-2017 10:53 AM
Clutch cable Fljay Triumph Bobber Forum General Discussion 5 10-24-2017 07:17 PM
Clutch cable warranty issue? Chris Mac Triumph Bobber Forum General Discussion 6 09-23-2017 06:53 PM

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome